-- Network Working Group O. Nicklass, Ed.
-- Request for Comments: 4805 RAD Data Communications, Ltd.
-- Obsoletes: 3895 March 2007
-- Category: Standards Track-- Definitions of Managed Objects
-- for the DS1, J1, E1, DS2, and E2 Interface TypesDS1-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,
NOTIFICATION-TYPE, transmission
FROM SNMPv2-SMI -- [RFC2578]DisplayString,TimeStamp,TruthValueFROM SNMPv2-TC -- [RFC2579]MODULE-COMPLIANCE,OBJECT-GROUP,NOTIFICATION-GROUPFROM SNMPv2-CONF -- [RFC2580]InterfaceIndex, ifIndex
FROM IF-MIB -- [RFC2863]PerfCurrentCount,PerfIntervalCount,PerfTotalCountFROM PerfHist-TC-MIB;-- [RFC3593]ds1 MODULE-IDENTITYLAST-UPDATED"200703050000Z"ORGANIZATION"IETF AToM MIB Working Group"CONTACT-INFO"WG charter:
http://www.ietf.org/html.charters/atommib-charter.html
Mailing Lists:
General Discussion: atommib@research.telcordia.com
To Subscribe: atommib-request@research.telcordia.com
Editor: Orly Nicklass
Postal: RAD Data Communications, Ltd.
Ziv Tower, 24 Roul Walenberg
Tel Aviv, Israel, 69719
Tel: +9723 765 9969
E-mail: orly_n@rad.com"DESCRIPTION"The MIB module to describe DS1, J1, E1, DS2, and
E2 interfaces objects.
Copyright (c) The IETF Trust (2007). This
version of this MIB module is part of RFC 4805;
see the RFC itself for full legal notices."REVISION"200703050000Z"DESCRIPTION"The following changes were made:
(1) Values were added to dsx1LineType to
support J1 types.
(2) The object dsx1LineImpedance was added.
(3) All DM-related objects were deprecated
following their removal from ITU performance
standards.
The RFC 4805 version of this MIB module."REVISION"200409090000Z"DESCRIPTION"The RFC 3895 version of this MIB module.
The key changes made to this MIB module
since its publication in RFC 2495 are as follows:
(1) The dsx1FracIfIndex SYNTAX matches the description
range.
(2) A value was added to dsx1TransmitClockSource.
(3) Values were added to dsx1LineType.
(4) Two objects were added, dsx1LineMode and
dsx1LineBuildOut, to better express transceiver
mode and LineBuildOut for T1.
(5) Reference was added to Circuit Identifier object.
(6) Align the DESCRIPTION clauses of few statistic
objects with the near-end definition, with the far-end
definition, and with RFC 3593.
(7) Changes in Compliance Statements to include new
objects.
(8) A typographical error in dsx2E2 was fixed; the new name
is dsx1E2."REVISION"199808011830Z"DESCRIPTION"The RFC 2495 version of this MIB module.
The key changes made to this MIB module
since its publication in RFC 1406 are as follows:
(1) The Fractional table has been deprecated.
(2) This document uses SMIv2.
(3) Usage is given for ifTable and ifXTable.
(4) Example usage of ifStackTable is included.
(5) dsx1IfIndex has been deprecated.
(6) Support for DS2 and E2 has been added.
(7) Additional lineTypes for DS2, E2, and unframed E1
were added.
(8) The definition of valid intervals has been clarified
for the case where the agent proxied for other
devices. In particular, the treatment of missing
intervals has been clarified.
(9) An inward loopback has been added.
(10) Additional lineStatus bits have been added for Near
End in Unavailable Signal State, Carrier Equipment
Out of Service, DS2 Payload AIS, and DS2 Performance
Threshold.
(11) A read-write line Length object has been added.
(12) Signal mode of other has been added.
(13) Added a lineStatus last change, trap and enabler.
(14) The e1(19) ifType has been obsoleted, so this MIB
does not list it as a supported ifType.
(15) Textual Conventions for statistics objects have
been used.
(16) A new object, dsx1LoopbackStatus, has been
introduced to reflect the loopbacks established
on a DS1 interface and the source to the requests.
dsx1LoopbackConfig continues to be the desired
loopback state while dsx1LoopbackStatus reflects
the actual state.
(17) A dual loopback has been added to allow the setting
of an inward loopback and a line loopback at the
same time.
(18) An object indicating which channel to use within a
parent object (i.e., DS3) has been added.
(19) An object has been added to indicate whether or
not this DS1/E1 is channelized.
(20) Line coding type of B6ZS has been added for DS2."REVISION"199301252028Z"DESCRIPTION"Initial version, published as RFC 1406."::={ transmission 18}-- note that this subsumes cept(19) and g703at2mb(67)-- there is no separate CEPT or G703AT2MB MIB-- The DS1 Near End Group-- The DS1 Near End Group consists of five tables:-- DS1 Configuration-- DS1 Current-- DS1 Interval
-- DS1 Total-- DS1 Channel Table-- The DS1 Configuration Tabledsx1ConfigTable OBJECT-TYPESYNTAXSEQUENCEOF Dsx1ConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The DS1 Configuration table."::={ ds1 6}dsx1ConfigEntry OBJECT-TYPESYNTAX Dsx1ConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the DS1 Configuration table."INDEX{ dsx1LineIndex }::={ dsx1ConfigTable 1}
Dsx1ConfigEntry ::=SEQUENCE{
dsx1LineIndex InterfaceIndex,
dsx1IfIndex InterfaceIndex,
dsx1TimeElapsed INTEGER,
dsx1ValidIntervals INTEGER,
dsx1LineType INTEGER,
dsx1LineCoding INTEGER,
dsx1SendCode INTEGER,
dsx1CircuitIdentifier DisplayString,
dsx1LoopbackConfig INTEGER,
dsx1LineStatus INTEGER,
dsx1SignalMode INTEGER,
dsx1TransmitClockSource INTEGER,
dsx1Fdl INTEGER,
dsx1InvalidIntervals INTEGER,
dsx1LineLength INTEGER,
dsx1LineStatusLastChange TimeStamp,
dsx1LineStatusChangeTrapEnable INTEGER,
dsx1LoopbackStatus INTEGER,
dsx1Ds1ChannelNumber INTEGER,
dsx1Channelization INTEGER,
dsx1LineMode INTEGER,
dsx1LineBuildOut INTEGER,
dsx1LineImpedance INTEGER}dsx1LineIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-only-- read-only since originally an-- SMIv1 indexSTATUScurrentDESCRIPTION"This object should be made equal to ifIndex. The
next paragraph describes its previous usage.
Making the object equal to ifIndex allows proper
use of the ifStackTable and ds0/ds0bundle MIBs.
Previously, this object was the identifier of a DS1
interface on a managed device. If there is an
ifEntry that is directly associated with this and
only this DS1 interface, it should have the same
value as ifIndex. Otherwise, number the
dsx1LineIndices with a unique identifier
following the rules of choosing a number that is
greater than ifNumber and numbering the inside
interfaces (e.g., equipment side) with even
numbers and outside interfaces (e.g., network
side) with odd numbers."::={ dsx1ConfigEntry 1}dsx1IfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"This value for this object is equal to the value
of ifIndex from the Interfaces table (RFC 2863)."::={ dsx1ConfigEntry 2}dsx1TimeElapsed OBJECT-TYPESYNTAXINTEGER(0..899)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of seconds that have elapsed since the
beginning of the near-end current error-
measurement period. If, for some reason, such as
an adjustment in the system's time-of-day clock,
the current interval exceeds the maximum value,
the agent will return the maximum value."::={ dsx1ConfigEntry 3}dsx1ValidIntervals OBJECT-TYPESYNTAXINTEGER(0..96)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of previous near-end intervals for
which data was collected. The value will be 96
unless the interface was brought online within the
last 24 hours, in which case the value will be the
number of complete 15-minute near-end intervals
since the interface has been online. In the case
where the agent is a proxy, it is possible that
some intervals are unavailable. In this case,
this interval is the maximum interval number for
which data is available."::={ dsx1ConfigEntry 4}dsx1LineType OBJECT-TYPESYNTAXINTEGER{other(1),dsx1ESF(2),dsx1D4(3),dsx1E1(4),dsx1E1CRC(5),dsx1E1MF(6),dsx1E1CRCMF(7),dsx1Unframed(8),dsx1E1Unframed(9),dsx1DS2M12(10),
dsx1E2(11),dsx1E1Q50(12),dsx1E1Q50CRC(13),dsx1J1ESF(14),dsx1J1Unframed(16)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This variable indicates the variety of DS1
Line implementing this circuit. The type of
circuit affects the number of bits per second
that the circuit can reasonably carry, as well
as the interpretation of the usage and error
statistics. The values, in sequence, describe:
TITLE: SPECIFICATION:
dsx1ESF Extended SuperFrame DS1
(T1.107)
dsx1D4 AT&T D4 format DS1 (T1.107)
dsx1E1 ITU-T G.704, (Table 5A)
dsx1E1-CRC ITU-T G.704, (Table 5B)
dsxE1-MF G.704 (Table 5A) with TS16
multiframing enabled
dsx1E1-CRC-MF G.704 (Table 5B) with TS16
multiframing enabled
dsx1Unframed DS1 with No Framing
dsx1E1Unframed E1 with No Framing (G.703)
dsx1DS2M12 DS2 frame format (T1.107)
dsx1E2 E2 frame format (G.704)
dsx1E1Q50 TS16 bits 5,7,8 set to 101,
[in all other cases it is set
to 111.] (G.704, table 14)
dsx1E1Q50CRC E1Q50 with CRC
dsx1J1ESF J1 according to (JT-G704,
JT-G706, and JT-I431)
dsx1J1Unframed J1 with No Framing
For clarification, the capacity for each E1 type
is as listed below:
dsx1E1Unframed - E1, no framing = 32 x 64k = 2048k
dsx1E1 or dsx1E1CRC - E1, with framing,
no signalling = 31 x 64k = 1984k
dsx1E1MF or dsx1E1CRCMF - E1, with framing,
signalling = 30 x 64k = 1920k"REFERENCE"American National Standard for
telecommunications -
digital hierarchy - formats specification,
ANSI T1.107- 1988.
ITU-T G.703: Physical/Electrical Characteristics
of Hierarchical Digital Interfaces, November
2001.
ITU-T G.704: Synchronous frame structures used at
1544, 6312, 2048, 8488 and 44 736 kbit/s
Hierarchical Levels, July 1995.
JT-G704: Synchronous frame structures used at
Primary and Secondary Hierarchical Levels,2002.
JT-G706. Frame Alignment and Cyclic Redundancy
Check (CRC) Procedures.
JT-I431. ISDN Primary Rate User-Network Interface,
Layer 1 Specifications, 2002 "::={ dsx1ConfigEntry 5}dsx1LineCoding OBJECT-TYPESYNTAXINTEGER{dsx1JBZS(1),dsx1B8ZS(2),dsx1HDB3(3),dsx1ZBTSI(4),dsx1AMI(5),other(6),
dsx1B6ZS(7)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
dsx1JBZS refers the Jammed Bit Zero Suppression,
in which the AT&T specification of at least one
pulse every 8-bit period is literally implemented
by forcing a pulse in bit 8 of each channel.
Thus, only 7 bits per channel, or 1.344 Mbps,
are available for data.
dsx1B8ZS refers to the use of a specified pattern
of normal bits and bipolar violations that are
used to replace a sequence of 8 zero bits.
ANSI Clear Channels may use dsx1ZBTSI, or Zero
Byte Time Slot Interchange.
E1 links, with or without CRC, use dsx1HDB3 or
dsx1AMI.
dsx1AMI refers to a mode wherein no Zero Code
Suppression is present and the line encoding does
not solve the problem directly. In this
application, the higher layer must provide data
that meets or exceeds the pulse density
requirements, such as inverting HDLC data.
dsx1B6ZS refers to the user of a specified pattern
of normal bits and bipolar violations that are
used to replace a sequence of 6 zero bits. Used
for DS2.
For more information about line coding see
[ANSI-T1.102]"::={ dsx1ConfigEntry 6}dsx1SendCode OBJECT-TYPESYNTAXINTEGER{dsx1SendNoCode(1),
dsx1SendLineCode(2),dsx1SendPayloadCode(3),dsx1SendResetCode(4),dsx1SendQRS(5),dsx1Send511Pattern(6),dsx1Send3in24Pattern(7),dsx1SendOtherTestPattern(8)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This variable indicates what type of code is
being sent across the DS1 interface by the device.
Setting this variable causes the interface to send
the code requested. The values mean the following:
dsx1SendNoCode
sending looped or normal data
dsx1SendLineCode
sending a request for a line loopback
dsx1SendPayloadCode
sending a request for a payload loopback
dsx1SendResetCode
sending a loopback termination request
dsx1SendQRS
sending a Quasi-Random Signal (QRS) test
pattern
dsx1Send511Pattern
sending a 511-bit fixed test pattern
dsx1Send3in24Pattern
sending a fixed test pattern of 3 bits set
in 24
dsx1SendOtherTestPattern
sending a test pattern other than those
described by this object"::={ dsx1ConfigEntry 7}dsx1CircuitIdentifier OBJECT-TYPESYNTAXDisplayString(SIZE(0..255))
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This variable contains the transmission vendor's
circuit identifier, for the purpose of
facilitating troubleshooting."REFERENCE"ITU-T M.1400"::={ dsx1ConfigEntry 8}dsx1LoopbackConfig OBJECT-TYPESYNTAXINTEGER{dsx1NoLoop(1),dsx1PayloadLoop(2),dsx1LineLoop(3),dsx1OtherLoop(4),dsx1InwardLoop(5),dsx1DualLoop(6)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This variable represents the desired loopback
configuration of the DS1 interface. Agents
supporting read/write access should return
inconsistentValue in response to a requested
loopback state that the interface does not
support. The values mean:
dsx1NoLoop
not in the loopback state. A device that is not
capable of performing a loopback on the interface
shall always return this as its value.
dsx1PayloadLoop
the received signal at this interface is looped
through the device. Typically, the received signal
is looped back for retransmission after it has
passed through the device's framing function.
dsx1LineLoop
the received signal at this interface does not go
through the device (minimum penetration) but is
looped back out.
dsx1OtherLoop
loopbacks that are not defined here.
dsx1InwardLoop
the transmitted signal at this interface is
looped back and received by the same interface.
What is transmitted onto the line is product
dependent.
dsx1DualLoop
both dsx1LineLoop and dsx1InwardLoop will be
active simultaneously."::={ dsx1ConfigEntry 9}dsx1LineStatus OBJECT-TYPESYNTAXINTEGER(1..131071)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable indicates the line status of the
interface. It contains loopback, failure,
received alarm and transmitted alarms
information.
The dsx1LineStatus is a bitmap represented as a
sum; therefore, it can represent multiple failures
(alarms) and a LoopbackState simultaneously.
dsx1NoAlarm must be set if and only if no other
flag is set.
If the dsx1loopbackState bit is set, the loopback
in effect can be determined from the
dsx1loopbackConfig object. The various bit
positions are as follows:
1 dsx1NoAlarm No alarm present
2 dsx1RcvFarEndLOF Far end LOF (a.k.a.
Yellow Alarm)
4 dsx1XmtFarEndLOF Near end sending LOF
indication
8 dsx1RcvAIS Far end sending AIS
16 dsx1XmtAIS Near end sending AIS
32 dsx1LossOfFrame Near end LOF (a.k.a.
Red Alarm)
64 dsx1LossOfSignal Near end Loss of Signal
128 dsx1LoopbackState Near end is looped
256 dsx1T16AIS E1 TS16 AIS
512 dsx1RcvFarEndLOMF Far end sending TS16 LOMF
1024 dsx1XmtFarEndLOMF Near end sending TS16 LOMF
2048 dsx1RcvTestCode Near end detects a test code
4096 dsx1OtherFailure Any line status not defined
here
8192 dsx1UnavailSigState Near end in unavailable
signal state
16384 dsx1NetEquipOOS Carrier equipment out of
service
32768 dsx1RcvPayloadAIS DS2 payload AIS
65536 dsx1Ds2PerfThreshold DS2 performance threshold
exceeded"::={ dsx1ConfigEntry 10}dsx1SignalMode OBJECT-TYPESYNTAXINTEGER{none(1),robbedBit(2),bitOriented(3),messageOriented(4),other(5)}MAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"'none' indicates that no bits are reserved for
signaling on this channel.
'robbedBit' indicates that DS1 Robbed Bit Signaling
is in use.
'bitOriented' indicates that E1 Channel Associated
Signaling is in use.
'messageOriented' indicates that Common Channel
Signaling is in use on either channel 16 of
an E1 link or channel 24 of a DS1."::={ dsx1ConfigEntry 11}dsx1TransmitClockSource OBJECT-TYPESYNTAXINTEGER{loopTiming(1),localTiming(2),throughTiming(3),adaptive (4)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The source of transmit clock.
'loopTiming' indicates that the recovered
receive clock is used as the transmit clock.
'localTiming' indicates that a local clock
source is used or when an external clock is
attached to the box containing the interface.
'throughTiming' indicates that recovered
receive clock from another interface is used as
the transmit clock.
'adaptive' indicates that the clock is recovered
based on the data flow and not based on the
physical layer"::={ dsx1ConfigEntry 12}dsx1Fdl OBJECT-TYPESYNTAXINTEGER(1..15)
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This bitmap describes the use of the
facilities data link and is the sum of the
capabilities. Set any bits that are appropriate:
other(1),
dsx1AnsiT1403(2),
dsx1Att54016(4),
dsx1FdlNone(8)
'other' indicates that a protocol other than
one of the following is used.
'dsx1AnsiT1403' refers to the FDL exchange
recommended by ANSI.
'dsx1Att54016' refers to ESF FDL exchanges.
'dsx1FdlNone' indicates that the device does
not use the FDL."::={ dsx1ConfigEntry 13}dsx1InvalidIntervals OBJECT-TYPESYNTAXINTEGER(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of intervals in the range from 0 to
dsx1ValidIntervals for which no data is available.
This object will typically be zero except in cases
where the data for some intervals is not
available (e.g., in proxy situations)."::={ dsx1ConfigEntry 14}dsx1LineLength OBJECT-TYPESYNTAXINTEGER(0..64000)UNITS"meters"MAX-ACCESSread-write
STATUScurrentDESCRIPTION"The length of the DS1 line in meters. This
object provides information for line build-out
circuitry. This object is only useful if the
interface has configurable line build-out
circuitry."::={ dsx1ConfigEntry 15}dsx1LineStatusLastChange OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The value of MIB II's sysUpTime object at the
time this DS1 entered its current line status
state. If the current state was entered prior to
the last re-initialization of the proxy-agent,
then this object contains a zero value."::={ dsx1ConfigEntry 16}dsx1LineStatusChangeTrapEnable OBJECT-TYPESYNTAXINTEGER{enabled(1),disabled(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates whether dsx1LineStatusChange traps
should be generated for this interface."DEFVAL{ disabled }::={ dsx1ConfigEntry 17}
dsx1LoopbackStatus OBJECT-TYPESYNTAXINTEGER(1..127)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable represents the current state of the
loopback on the DS1 interface. It contains
information about loopbacks established by a
manager and remotely from the far end.
The dsx1LoopbackStatus is a bitmap represented as
a sum; therefore, it can represent multiple
loopbacks simultaneously.
The various bit positions are as follows:
1 dsx1NoLoopback
2 dsx1NearEndPayloadLoopback
4 dsx1NearEndLineLoopback
8 dsx1NearEndOtherLoopback
16 dsx1NearEndInwardLoopback
32 dsx1FarEndPayloadLoopback
64 dsx1FarEndLineLoopback"::={ dsx1ConfigEntry 18}dsx1Ds1ChannelNumber OBJECT-TYPESYNTAXINTEGER(0..28)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable represents the channel number of
the DS1/E1 on its parent DS2/E2 or DS3/E3. A
value of 0 indicates that this DS1/E1 does not
have a parent DS3/E3."::={ dsx1ConfigEntry 19}dsx1Channelization OBJECT-TYPE
SYNTAXINTEGER{disabled(1),enabledDs0(2),enabledDs1(3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates whether this DS1/E1 or DS2 is
channelized or unchannelized.
The value of enabledDs0(2) indicates that this is a
DS1 channelized into DS0s. Setting this value will
cause the creation, and resetting it to disabled(1)
will cause the deletion of entries in the ifTable
for the DS0s that are within the DS1.
The value of enabledDs1(3) indicates that this is a
DS2 channelized into DS1s. Setting this value will
cause the creation, and resetting it to disabled(1)
will cause the deletion of entries in the ifTable
for the DS1s that are within the DS2."::={ dsx1ConfigEntry 20}dsx1LineMode OBJECT-TYPESYNTAXINTEGER{csu(1),dsu(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This setting puts the T1 framer into either
long-haul (CSU) mode or short-haul (DSU) mode."
::={ dsx1ConfigEntry 21}dsx1LineBuildOut OBJECT-TYPESYNTAXINTEGER{notApplicable(1),neg75dB(2),neg15dB(3),neg225dB(4),zerodB(5)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Attenuation setting for T1 framer in long haul
(CSU) mode. The optional values are -7.5dB,
-15dB, -22.5dB, and 0dB."::={ dsx1ConfigEntry 22}dsx1LineImpedance OBJECT-TYPESYNTAXINTEGER{notApplicable(1),unbalanced75ohms(2),balanced100ohms(3),balanced120ohms(4)}MAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"Nominal line impedance. For T1 and J1 lines, the
value is typically balanced100ohms(3). For E1
lines, the value is typically unbalanced75ohms(2)
and balanced120ohms(4). When this object does not
apply, or when the appropriate value is not known,
the value should be set to notApplicable(1)."::={ dsx1ConfigEntry 23}-- The DS1 Current Tabledsx1CurrentTable OBJECT-TYPESYNTAXSEQUENCEOF Dsx1CurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The DS1 Current table contains various statistics
being collected for the current 15-minute
interval."::={ ds1 7}dsx1CurrentEntry OBJECT-TYPESYNTAX Dsx1CurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the DS1 Current table."INDEX{ dsx1CurrentIndex }::={ dsx1CurrentTable 1}
Dsx1CurrentEntry ::=SEQUENCE{
dsx1CurrentIndex InterfaceIndex,
dsx1CurrentESs PerfCurrentCount,
dsx1CurrentSESs PerfCurrentCount,
dsx1CurrentSEFSs PerfCurrentCount,
dsx1CurrentUASs PerfCurrentCount,
dsx1CurrentCSSs PerfCurrentCount,
dsx1CurrentPCVs PerfCurrentCount,
dsx1CurrentLESs PerfCurrentCount,
dsx1CurrentBESs PerfCurrentCount,
dsx1CurrentDMs PerfCurrentCount,
dsx1CurrentLCVs PerfCurrentCount}dsx1CurrentIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-only-- read-only since originally an-- SMIv1 indexSTATUScurrentDESCRIPTION"The index value that uniquely identifies the DS1
interface to which this entry is applicable. The
interface identified by a particular value of this
index is the same interface as identified by the
same value as a dsx1LineIndex object instance."::={ dsx1CurrentEntry 1}dsx1CurrentESs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Errored Seconds."::={ dsx1CurrentEntry 2}dsx1CurrentSESs OBJECT-TYPE
SYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Severely Errored Seconds."::={ dsx1CurrentEntry 3}dsx1CurrentSEFSs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Severely Errored Framing Seconds."::={ dsx1CurrentEntry 4}dsx1CurrentUASs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Unavailable Seconds."::={ dsx1CurrentEntry 5}dsx1CurrentCSSs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Controlled Slip Seconds."::={ dsx1CurrentEntry 6}dsx1CurrentPCVs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-only
STATUScurrentDESCRIPTION"The number of Path Coding Violations."::={ dsx1CurrentEntry 7}dsx1CurrentLESs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Line Errored Seconds."::={ dsx1CurrentEntry 8}dsx1CurrentBESs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Bursty Errored Seconds."::={ dsx1CurrentEntry 9}dsx1CurrentDMs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"The number of Degraded Minutes."::={ dsx1CurrentEntry 10}dsx1CurrentLCVs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Line Coding Violations (LCVs)."
::={ dsx1CurrentEntry 11}-- The DS1 Interval Tabledsx1IntervalTable OBJECT-TYPESYNTAXSEQUENCEOF Dsx1IntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The DS1 Interval table contains various
statistics collected by each DS1 interface over
the previous 24 hours of operation. The past 24
hours are broken into 96 completed 15-minute
intervals. Each row in this table represents one
such interval (identified by dsx1IntervalNumber)
for one specific instance (identified by
dsx1IntervalIndex)."::={ ds1 8}dsx1IntervalEntry OBJECT-TYPESYNTAX Dsx1IntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the DS1 Interval table."INDEX{ dsx1IntervalIndex, dsx1IntervalNumber }::={ dsx1IntervalTable 1}
Dsx1IntervalEntry ::=SEQUENCE{
dsx1IntervalIndex InterfaceIndex,
dsx1IntervalNumber INTEGER,
dsx1IntervalESs PerfIntervalCount,
dsx1IntervalSESs PerfIntervalCount,
dsx1IntervalSEFSs PerfIntervalCount,
dsx1IntervalUASs PerfIntervalCount,
dsx1IntervalCSSs PerfIntervalCount,
dsx1IntervalPCVs PerfIntervalCount,
dsx1IntervalLESs PerfIntervalCount,
dsx1IntervalBESs PerfIntervalCount,
dsx1IntervalDMs PerfIntervalCount,
dsx1IntervalLCVs PerfIntervalCount,
dsx1IntervalValidData TruthValue}dsx1IntervalIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-only-- read-only since originally an-- SMIv1 indexSTATUScurrentDESCRIPTION"The index value that uniquely identifies the DS1
interface to which this entry is applicable. The
interface identified by a particular value of this
index is the same interface as identified by the
same value as a dsx1LineIndex object instance."::={ dsx1IntervalEntry 1}dsx1IntervalNumber OBJECT-TYPESYNTAXINTEGER(1..96)MAX-ACCESSread-only-- read-only since originally an-- SMIv1 index
STATUScurrentDESCRIPTION"A number between 1 and 96, where 1 is the most
recently completed 15-minute interval and 96 is
the 15-minute interval completed 23 hours and 45
minutes prior to interval 1."::={ dsx1IntervalEntry 2}dsx1IntervalESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Errored Seconds."::={ dsx1IntervalEntry 3}dsx1IntervalSESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Severely Errored Seconds."::={ dsx1IntervalEntry 4}dsx1IntervalSEFSs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Severely Errored Framing Seconds."::={ dsx1IntervalEntry 5}dsx1IntervalUASs OBJECT-TYPESYNTAXPerfIntervalCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Unavailable Seconds. This object
may decrease if the occurrence of unavailable
seconds occurs across an interval boundary."::={ dsx1IntervalEntry 6}dsx1IntervalCSSs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Controlled Slip Seconds."::={ dsx1IntervalEntry 7}dsx1IntervalPCVs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Path Coding Violations."::={ dsx1IntervalEntry 8}dsx1IntervalLESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Line Errored Seconds."::={ dsx1IntervalEntry 9}dsx1IntervalBESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-only
STATUScurrentDESCRIPTION"The number of Bursty Errored Seconds."::={ dsx1IntervalEntry 10}dsx1IntervalDMs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"The number of Degraded Minutes."::={ dsx1IntervalEntry 11}dsx1IntervalLCVs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Line Coding Violations."::={ dsx1IntervalEntry 12}dsx1IntervalValidData OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable indicates whether the data for this
interval is valid."::={ dsx1IntervalEntry 13}-- The DS1 Total Tabledsx1TotalTable OBJECT-TYPESYNTAXSEQUENCEOF Dsx1TotalEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"The DS1 Total table contains the cumulative sum
of the various statistics for the 24-hour period
preceding the current interval."::={ ds1 9}dsx1TotalEntry OBJECT-TYPESYNTAX Dsx1TotalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the DS1 Total table."INDEX{ dsx1TotalIndex }::={ dsx1TotalTable 1}
Dsx1TotalEntry ::=SEQUENCE{
dsx1TotalIndex InterfaceIndex,
dsx1TotalESs PerfTotalCount,
dsx1TotalSESs PerfTotalCount,
dsx1TotalSEFSs PerfTotalCount,
dsx1TotalUASs PerfTotalCount,
dsx1TotalCSSs PerfTotalCount,
dsx1TotalPCVs PerfTotalCount,
dsx1TotalLESs PerfTotalCount,
dsx1TotalBESs PerfTotalCount,
dsx1TotalDMs PerfTotalCount,
dsx1TotalLCVs PerfTotalCount}dsx1TotalIndex OBJECT-TYPE
SYNTAXInterfaceIndexMAX-ACCESSread-only-- read-only since originally an-- SMIv1 indexSTATUScurrentDESCRIPTION"The index value that uniquely identifies the DS1
interface to which this entry is applicable. The
interface identified by a particular value of this
index is the same interface as identified by the
same value as a dsx1LineIndex object instance."::={ dsx1TotalEntry 1}dsx1TotalESs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Errored Seconds encountered by a DS1
interface in the previous 24-hour interval.
Invalid 15-minute intervals count as 0."::={ dsx1TotalEntry 2}dsx1TotalSESs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Severely Errored Seconds
encountered by a DS1 interface in the previous
24-hour interval. Invalid 15-minute intervals
count as 0."::={ dsx1TotalEntry 3}dsx1TotalSEFSs OBJECT-TYPESYNTAXPerfTotalCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Severely Errored Framing Seconds
encountered by a DS1 interface in the previous
24-hour interval. Invalid 15-minute intervals
count as 0."::={ dsx1TotalEntry 4}dsx1TotalUASs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Unavailable Seconds encountered by
a DS1 interface in the previous 24-hour interval.
Invalid 15-minute intervals count as 0."::={ dsx1TotalEntry 5}dsx1TotalCSSs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Controlled Slip Seconds encountered
by a DS1 interface in the previous 24-hour
interval. Invalid 15-minute intervals count as
0."::={ dsx1TotalEntry 6}dsx1TotalPCVs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Path Coding Violations encountered
by a DS1 interface in the previous 24-hour
interval. Invalid 15-minute intervals count as
0."::={ dsx1TotalEntry 7}dsx1TotalLESs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Line Errored Seconds encountered by
a DS1 interface in the previous 24-hour interval.
Invalid 15-minute intervals count as 0."::={ dsx1TotalEntry 8}dsx1TotalBESs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Bursty Errored Seconds (BESs)
encountered by a DS1 interface in the previous
24-hour interval. Invalid 15-minute intervals count
as 0."::={ dsx1TotalEntry 9}dsx1TotalDMs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"The number of Degraded Minutes (DMs) encountered
by a DS1 interface in the previous 24-hour
interval. Invalid 15-minute intervals count as
0."::={ dsx1TotalEntry 10}
dsx1TotalLCVs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Line Coding Violations (LCVs)
encountered by a DS1 interface in the current
15-minute interval. Invalid 15-minute intervals
count as 0."::={ dsx1TotalEntry 11}-- The DS1 Channel Tabledsx1ChanMappingTable OBJECT-TYPESYNTAXSEQUENCEOF Dsx1ChanMappingEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The DS1 Channel Mapping table. This table maps a
DS1 channel number on a particular DS3 into an
ifIndex. In the presence of DS2s, this table can
be used to map a DS2 channel number on a DS3 into
an ifIndex, or used to map a DS1 channel number on
a DS2 into an ifIndex."::={ ds1 16}dsx1ChanMappingEntry OBJECT-TYPESYNTAX Dsx1ChanMappingEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the DS1 Channel Mapping table. There
is an entry in this table corresponding to each
DS1 ifEntry within any interface that is
channelized to the individual DS1 ifEntry level.
This table is intended to facilitate mapping from
channelized interface / channel number to DS1
ifEntry (e.g., mapping (DS3 ifIndex, DS1 channel
number) -> ifIndex).
While this table provides information that can
also be found in the ifStackTable and
dsx1ConfigTable, it provides this same information
with a single table lookup, rather than by walking
the ifStackTable to find the various constituent
DS1 ifTable entries, and testing various
dsx1ConfigTable entries to check for the entry
with the applicable DS1 channel number."INDEX{ ifIndex, dsx1Ds1ChannelNumber }::={ dsx1ChanMappingTable 1}
Dsx1ChanMappingEntry ::=SEQUENCE{
dsx1ChanMappedIfIndex InterfaceIndex}dsx1ChanMappedIfIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the ifIndex value assigned
by the agent for the individual DS1 ifEntry that
corresponds to the given DS1 channel number
(specified by the INDEX element
dsx1Ds1ChannelNumber) of the given channelized
interface (specified by INDEX element ifIndex)."::={ dsx1ChanMappingEntry 1}-- The DS1 Far End Current Tabledsx1FarEndCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF Dsx1FarEndCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"The DS1 Far End Current table contains various
statistics being collected for the current
15-minute interval. The statistics are collected
from the far-end messages on the Facilities Data
Link. The definitions are the same as described
for the near-end information."::={ ds1 10}dsx1FarEndCurrentEntry OBJECT-TYPESYNTAX Dsx1FarEndCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the DS1 Far End Current table."INDEX{ dsx1FarEndCurrentIndex }::={ dsx1FarEndCurrentTable 1}
Dsx1FarEndCurrentEntry ::=SEQUENCE{
dsx1FarEndCurrentIndex InterfaceIndex,
dsx1FarEndTimeElapsed INTEGER,
dsx1FarEndValidIntervals INTEGER,
dsx1FarEndCurrentESs PerfCurrentCount,
dsx1FarEndCurrentSESs PerfCurrentCount,
dsx1FarEndCurrentSEFSs PerfCurrentCount,
dsx1FarEndCurrentUASs PerfCurrentCount,
dsx1FarEndCurrentCSSs PerfCurrentCount,
dsx1FarEndCurrentLESs PerfCurrentCount,
dsx1FarEndCurrentPCVs PerfCurrentCount,
dsx1FarEndCurrentBESs PerfCurrentCount,
dsx1FarEndCurrentDMs PerfCurrentCount,
dsx1FarEndInvalidIntervals INTEGER}dsx1FarEndCurrentIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-only-- read-only since originally an-- SMIv1 indexSTATUScurrentDESCRIPTION"The index value that uniquely identifies the DS1
interface to which this entry is applicable. The
interface identified by a particular value of this
index is identical to the interface identified by
the same value of dsx1LineIndex."::={ dsx1FarEndCurrentEntry 1}dsx1FarEndTimeElapsed OBJECT-TYPESYNTAXINTEGER(0..899)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of seconds that have elapsed since the
beginning of the far-end current error-measurement
period. If, for some reason, such as an adjustment
in the system's time-of-day clock, the current
interval exceeds the maximum value, the agent will
return the maximum value."::={ dsx1FarEndCurrentEntry 2}dsx1FarEndValidIntervals OBJECT-TYPESYNTAXINTEGER(0..96)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of previous far-end intervals for
which data was collected. The value will be 96
unless the interface was brought online within the
last 24 hours, in which case the value will be the
number of complete 15-minute far-end intervals
since the interface has been online. In the case
where the agent is a proxy, it is possible that
some intervals are unavailable. In this case,
this interval is the maximum interval number for
which data is available."::={ dsx1FarEndCurrentEntry 3}dsx1FarEndCurrentESs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Errored Seconds."::={ dsx1FarEndCurrentEntry 4}dsx1FarEndCurrentSESs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Severely Errored Seconds."::={ dsx1FarEndCurrentEntry 5}dsx1FarEndCurrentSEFSs OBJECT-TYPESYNTAXPerfCurrentCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Severely Errored Framing
Seconds."::={ dsx1FarEndCurrentEntry 6}dsx1FarEndCurrentUASs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Unavailable Seconds."::={ dsx1FarEndCurrentEntry 7}dsx1FarEndCurrentCSSs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Controlled Slip Seconds."::={ dsx1FarEndCurrentEntry 8}dsx1FarEndCurrentLESs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Line Errored Seconds."::={ dsx1FarEndCurrentEntry 9}dsx1FarEndCurrentPCVs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-only
STATUScurrentDESCRIPTION"The number of Far End Path Coding Violations."::={ dsx1FarEndCurrentEntry 10}dsx1FarEndCurrentBESs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Bursty Errored Seconds."::={ dsx1FarEndCurrentEntry 11}dsx1FarEndCurrentDMs OBJECT-TYPESYNTAXPerfCurrentCountMAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"The number of Far End Degraded Minutes."::={ dsx1FarEndCurrentEntry 12}dsx1FarEndInvalidIntervals OBJECT-TYPESYNTAXINTEGER(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of intervals in the range from 0 to
dsx1FarEndValidIntervals for which no data is
available. This object will typically be zero
except in cases where the data for some intervals
is not available (e.g., in proxy situations)."::={ dsx1FarEndCurrentEntry 13}
-- The DS1 Far End Interval Tabledsx1FarEndIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF Dsx1FarEndIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The DS1 Far End Interval table contains various
statistics collected by each DS1 interface over
the previous 24 hours of operation. The past 24
hours are broken into 96 completed 15-minute
intervals. Each row in this table represents one
such interval (identified by
dsx1FarEndIntervalNumber) for one specific
instance (identified by dsx1FarEndIntervalIndex)."::={ ds1 11}dsx1FarEndIntervalEntry OBJECT-TYPESYNTAX Dsx1FarEndIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the DS1 Far End Interval table."INDEX{ dsx1FarEndIntervalIndex,
dsx1FarEndIntervalNumber }::={ dsx1FarEndIntervalTable 1}
Dsx1FarEndIntervalEntry ::=SEQUENCE{
dsx1FarEndIntervalIndex InterfaceIndex,
dsx1FarEndIntervalNumber INTEGER,
dsx1FarEndIntervalESs PerfIntervalCount,
dsx1FarEndIntervalSESs PerfIntervalCount,
dsx1FarEndIntervalSEFSs PerfIntervalCount,
dsx1FarEndIntervalUASs PerfIntervalCount,
dsx1FarEndIntervalCSSs PerfIntervalCount,
dsx1FarEndIntervalLESs PerfIntervalCount,
dsx1FarEndIntervalPCVs PerfIntervalCount,
dsx1FarEndIntervalBESs PerfIntervalCount,
dsx1FarEndIntervalDMs PerfIntervalCount,
dsx1FarEndIntervalValidData TruthValue}dsx1FarEndIntervalIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-only-- read-only since originally an-- SMIv1 indexSTATUScurrentDESCRIPTION"The index value that uniquely identifies the DS1
interface to which this entry is applicable. The
interface identified by a particular value of this
index is identical to the interface identified by
the same value of dsx1LineIndex."::={ dsx1FarEndIntervalEntry 1}dsx1FarEndIntervalNumber OBJECT-TYPESYNTAXINTEGER(1..96)MAX-ACCESSread-only-- read-only since originally an-- SMIv1 index
STATUScurrentDESCRIPTION"A number between 1 and 96, where 1 is the most
recently completed 15-minute interval and 96 is
the 15 minutes interval completed 23 hours and 45
minutes prior to interval 1."::={ dsx1FarEndIntervalEntry 2}dsx1FarEndIntervalESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Errored Seconds."::={ dsx1FarEndIntervalEntry 3}dsx1FarEndIntervalSESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Severely Errored Seconds."::={ dsx1FarEndIntervalEntry 4}dsx1FarEndIntervalSEFSs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Severely Errored Framing
Seconds."::={ dsx1FarEndIntervalEntry 5}dsx1FarEndIntervalUASs OBJECT-TYPESYNTAXPerfIntervalCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Unavailable Seconds."::={ dsx1FarEndIntervalEntry 6}dsx1FarEndIntervalCSSs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Controlled Slip Seconds."::={ dsx1FarEndIntervalEntry 7}dsx1FarEndIntervalLESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Line Errored Seconds."::={ dsx1FarEndIntervalEntry 8}dsx1FarEndIntervalPCVs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Path Coding Violations."::={ dsx1FarEndIntervalEntry 9}dsx1FarEndIntervalBESs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-only
STATUScurrentDESCRIPTION"The number of Far End Bursty Errored Seconds."::={ dsx1FarEndIntervalEntry 10}dsx1FarEndIntervalDMs OBJECT-TYPESYNTAXPerfIntervalCountMAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"The number of Far End Degraded Minutes."::={ dsx1FarEndIntervalEntry 11}dsx1FarEndIntervalValidData OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION" This variable indicates if the data for this
interval is valid."::={ dsx1FarEndIntervalEntry 12}-- The DS1 Far End Total Tabledsx1FarEndTotalTable OBJECT-TYPESYNTAXSEQUENCEOF Dsx1FarEndTotalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The DS1 Far End Total table contains the
cumulative sum of the various statistics for the
24-hour period preceding the current interval."::={ ds1 12}dsx1FarEndTotalEntry OBJECT-TYPE
SYNTAX Dsx1FarEndTotalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the DS1 Far End Total table."INDEX{ dsx1FarEndTotalIndex }::={ dsx1FarEndTotalTable 1}
Dsx1FarEndTotalEntry ::=SEQUENCE{
dsx1FarEndTotalIndex InterfaceIndex,
dsx1FarEndTotalESs PerfTotalCount,
dsx1FarEndTotalSESs PerfTotalCount,
dsx1FarEndTotalSEFSs PerfTotalCount,
dsx1FarEndTotalUASs PerfTotalCount,
dsx1FarEndTotalCSSs PerfTotalCount,
dsx1FarEndTotalLESs PerfTotalCount,
dsx1FarEndTotalPCVs PerfTotalCount,
dsx1FarEndTotalBESs PerfTotalCount,
dsx1FarEndTotalDMs PerfTotalCount}dsx1FarEndTotalIndex OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSread-only-- read-only since originally an-- SMIv1 indexSTATUScurrentDESCRIPTION"The index value that uniquely identifies the DS1
interface to which this entry is applicable. The
interface identified by a particular value of this
index is identical to the interface identified by
the same value of dsx1LineIndex."::={ dsx1FarEndTotalEntry 1}dsx1FarEndTotalESs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Errored Seconds encountered
by a DS1 interface in the previous 24-hour
interval. Invalid 15-minute intervals count as
0."::={ dsx1FarEndTotalEntry 2}dsx1FarEndTotalSESs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Severely Errored Seconds
encountered by a DS1 interface in the previous
24-hour interval. Invalid 15-minute intervals
count as 0."::={ dsx1FarEndTotalEntry 3}dsx1FarEndTotalSEFSs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Severely Errored Framing
Seconds encountered by a DS1 interface in the
previous 24-hour interval. Invalid 15-minute
intervals count as 0."
::={ dsx1FarEndTotalEntry 4}dsx1FarEndTotalUASs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Unavailable Seconds encountered by
a DS1 interface in the previous 24-hour interval.
Invalid 15-minute intervals count as 0."::={ dsx1FarEndTotalEntry 5}dsx1FarEndTotalCSSs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Controlled Slip Seconds
encountered by a DS1 interface in the previous
24-hour interval. Invalid 15 minute intervals
count as 0."::={ dsx1FarEndTotalEntry 6}dsx1FarEndTotalLESs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Line Errored Seconds
encountered by a DS1 interface in the previous
24-hour interval. Invalid 15-minute intervals
count as 0."::={ dsx1FarEndTotalEntry 7}dsx1FarEndTotalPCVs OBJECT-TYPESYNTAXPerfTotalCount
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Far End Path Coding Violations
reported via the far end block error count
encountered by a DS1 interface in the previous
24-hour interval. Invalid 15-minute intervals
count as 0."::={ dsx1FarEndTotalEntry 8}dsx1FarEndTotalBESs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Bursty Errored Seconds (BESs)
encountered by a DS1 interface in the previous
24-hour interval. Invalid 15-minute intervals
count as 0."::={ dsx1FarEndTotalEntry 9}dsx1FarEndTotalDMs OBJECT-TYPESYNTAXPerfTotalCountMAX-ACCESSread-onlySTATUSdeprecatedDESCRIPTION"The number of Degraded Minutes (DMs) encountered
by a DS1 interface in the previous 24-hour
interval. Invalid 15-minute intervals count as
0."::={ dsx1FarEndTotalEntry 10}-- The DS1 Fractional Tabledsx1FracTable OBJECT-TYPESYNTAXSEQUENCEOF Dsx1FracEntry
MAX-ACCESSnot-accessible
STATUSdeprecatedDESCRIPTION"This table is deprecated in favor of using
ifStackTable.
The table was mandatory for systems dividing a DS1
into channels containing different data streams
that are of local interest. Systems that are
indifferent to data content, such as CSUs, need
not implement it.
The DS1 Fractional table identifies which DS1
channels associated with a CSU are being used to
support a logical interface, i.e., an entry in the
interfaces table from the Internet-standard MIB.
For example, consider an application managing a
North American ISDN Primary Rate link whose
division is a 384-kbit/s H1 _B_ Channel for video,
a second H1 for data to a primary routing peer,
and 12 64-kbit/s H0 _B_ Channels. Consider that
some subset of the H0 channels is used for voice
and the remainder are available for dynamic data
calls.
We count a total of 14 interfaces multiplexed onto
the DS1 interface. Six DS1 channels (for the sake
of the example, channels 1..6) are used for video,
six more (7..11 and 13) are used for data, and the
remaining 12 are in channels 12 and 14..24.
Let us further imagine that ifIndex 2 is of type
DS1 and refers to the DS1 interface and that the
interfaces layered onto it are numbered 3..16.
We might describe the allocation of channels, in
the dsx1FracTable, as follows:
dsx1FracIfIndex.2. 1 = 3 dsx1FracIfIndex.2.13 = 4
dsx1FracIfIndex.2. 2 = 3 dsx1FracIfIndex.2.14 = 6
dsx1FracIfIndex.2. 3 = 3 dsx1FracIfIndex.2.15 = 7
dsx1FracIfIndex.2. 4 = 3 dsx1FracIfIndex.2.16 = 8
dsx1FracIfIndex.2. 5 = 3 dsx1FracIfIndex.2.17 = 9
dsx1FracIfIndex.2. 6 = 3 dsx1FracIfIndex.2.18 = 10
dsx1FracIfIndex.2. 7 = 4 dsx1FracIfIndex.2.19 = 11
dsx1FracIfIndex.2. 8 = 4 dsx1FracIfIndex.2.20 = 12
dsx1FracIfIndex.2. 9 = 4 dsx1FracIfIndex.2.21 = 13
dsx1FracIfIndex.2.10 = 4 dsx1FracIfIndex.2.22 = 14
dsx1FracIfIndex.2.11 = 4 dsx1FracIfIndex.2.23 = 15
dsx1FracIfIndex.2.12 = 5 dsx1FracIfIndex.2.24 = 16
For North American (DS1) interfaces, there are 24
legal channels, numbered 1 through 24.
For G.704 interfaces, there are 31 legal channels,
numbered 1 through 31. The channels (1..31)
correspond directly to the equivalently numbered
time-slots."::={ ds1 13}dsx1FracEntry OBJECT-TYPESYNTAX Dsx1FracEntry
MAX-ACCESSnot-accessibleSTATUSdeprecatedDESCRIPTION"An entry in the DS1 Fractional table."INDEX{ dsx1FracIndex, dsx1FracNumber }::={ dsx1FracTable 1}
Dsx1FracEntry ::=SEQUENCE{
dsx1FracIndex INTEGER,
dsx1FracNumber INTEGER,
dsx1FracIfIndex INTEGER}dsx1FracIndex OBJECT-TYPESYNTAXINTEGER(1..'7fffffff'h)MAX-ACCESSread-only-- read-only since originally an-- SMIv1 indexSTATUSdeprecated
DESCRIPTION"The index value that uniquely identifies the
DS1 interface to which this entry is applicable.
The interface identified by a particular
value of this index is the same interface as
identified by the same value as a dsx1LineIndex
object instance."::={ dsx1FracEntry 1}dsx1FracNumber OBJECT-TYPESYNTAXINTEGER(1..31)MAX-ACCESSread-only-- read-only since originally an-- SMIv1 indexSTATUSdeprecatedDESCRIPTION"The channel number for this entry."::={ dsx1FracEntry 2}dsx1FracIfIndex OBJECT-TYPESYNTAXINTEGER(0..'7fffffff'h)MAX-ACCESSread-writeSTATUSdeprecatedDESCRIPTION"An index value that uniquely identifies an
interface. The interface identified by a particular
value of this index is the same interface
as identified by the same value as an ifIndex
object instance. If no interface is currently using
a channel, the value should be zero. If a
single interface occupies more than one time-slot,
that ifIndex value will be found in multiple
time-slots."::={ dsx1FracEntry 3}
-- DS1 TRAPSds1Traps OBJECTIDENTIFIER::={ ds1 15}dsx1LineStatusChange NOTIFICATION-TYPEOBJECTS{ dsx1LineStatus,
dsx1LineStatusLastChange }STATUScurrentDESCRIPTION"A dsx1LineStatusChange trap is sent when the
value of an instance dsx1LineStatus changes. It
can be utilized by an Network Management Station
(NMS) to trigger polls. When the line status
change results from a higher-level line status
change (i.e., DS3), then no traps for the DS1
are sent."::={ ds1Traps 01}-- conformance informationds1Conformance OBJECTIDENTIFIER::={ ds1 14}ds1Groups OBJECTIDENTIFIER::={ ds1Conformance 1}ds1Compliances OBJECTIDENTIFIER::={ ds1Conformance 2}-- compliance statementsds1Compliance MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"The compliance statement for T1 and E1
interfaces."MODULE-- this moduleMANDATORY-GROUPS{ ds1NearEndConfigGroup,
ds1NearEndStatisticsGroup }GROUP ds1FarEndGroup
DESCRIPTION"Implementation of this group is optional for all
systems that attach to a DS1 interface."GROUP ds1NearEndOptionalConfigGroup
DESCRIPTION"Implementation of this group is optional for all
systems that attach to a DS1 interface."GROUP ds1DS2Group
DESCRIPTION"Implementation of this group is mandatory for all
systems that attach to a DS2 interface."GROUP ds1TransStatsGroup
DESCRIPTION"This group is the set of statistics appropriate
for all systems that attach to a DS1 interface
running transparent or unFramed lineType."GROUP ds1ChanMappingGroup
DESCRIPTION"This group is the set of objects for mapping a
DS3 Channel (dsx1Ds1ChannelNumber) to ifIndex.
Implementation of this group is mandatory for
systems that support the channelization of DS3s
into DS1s."OBJECT dsx1LineType
SYNTAXINTEGER{
other(1),
dsx1ESF(2),
dsx1D4(3),
dsx1E1(4),
dsx1E1CRC(5),
dsx1E1MF(6),
dsx1E1CRCMF(7),
dsx1Unframed(8),
dsx1E1Unframed(9),
dsx1DS2M12(10),
dsx1E2(11)}MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line type is not
required."OBJECT dsx1LineCoding
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line coding is not
required."OBJECT dsx1SendCode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the send code is not
required."OBJECT dsx1LoopbackConfig
MIN-ACCESSread-onlyDESCRIPTION"The ability to set loopbacks is not required."OBJECT dsx1SignalMode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the signal mode is not
required."OBJECT dsx1TransmitClockSource
SYNTAXINTEGER{
loopTiming(1),
localTiming(2),
throughTiming(3)}MIN-ACCESSread-onlyDESCRIPTION"The ability to set the transmit clock source is
not required."OBJECT dsx1Fdl
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the FDL is not required."OBJECT dsx1LineLength
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line length is not
required."OBJECT dsx1Channelization
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the channelization is not
required."::={ ds1Compliances 1}ds1MibT1PriCompliance MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"Compliance statement for using this MIB for ISDN
Primary Rate interfaces on T1 lines."MODULEMANDATORY-GROUPS{ ds1NearEndConfigGroup,
ds1NearEndStatisticsGroup }OBJECT dsx1LineType
SYNTAXINTEGER{
dsx1ESF(2)-- Intl Spec would be G704(2)-- or I.431(4)}MIN-ACCESSread-onlyDESCRIPTION"Line type for T1 ISDN Primary Rate
interfaces."OBJECT dsx1LineCoding
SYNTAXINTEGER{
dsx1B8ZS(2)}MIN-ACCESSread-onlyDESCRIPTION"Type of Zero Code Suppression for
T1 ISDN Primary Rate interfaces."OBJECT dsx1SignalMode
SYNTAXINTEGER{
none(1),-- if there is no signaling channel
messageOriented(4)}MIN-ACCESSread-onlyDESCRIPTION"Possible signaling modes for
T1 ISDN Primary Rate interfaces."OBJECT dsx1TransmitClockSource
SYNTAXINTEGER{
loopTiming(1)}MIN-ACCESSread-onlyDESCRIPTION"The transmit clock is derived from
received clock on ISDN Primary Rate
interfaces."OBJECT dsx1Fdl
MIN-ACCESSread-onlyDESCRIPTION"Facilities Data Link usage on T1 ISDN
Primary Rate interfaces.
Note: Eventually, dsx1Att-54016(4) is to be
used here since the line type is ESF."OBJECT dsx1Channelization
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the channelization
is not required."::={ ds1Compliances 2}ds1MibE1PriCompliance MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"Compliance statement for using this MIB for ISDN
Primary Rate interfaces on E1 lines."MODULEMANDATORY-GROUPS{ ds1NearEndConfigGroup,
ds1NearEndStatisticsGroup }OBJECT dsx1LineType
SYNTAXINTEGER{
dsx1E1CRC(5)}MIN-ACCESSread-onlyDESCRIPTION"Line type for E1 ISDN Primary Rate
interfaces."OBJECT dsx1LineCoding
SYNTAXINTEGER{
dsx1HDB3(3)}
MIN-ACCESSread-onlyDESCRIPTION"Type of Zero Code Suppression for
E1 ISDN Primary Rate interfaces."OBJECT dsx1SignalMode
SYNTAXINTEGER{
messageOriented(4)}MIN-ACCESSread-onlyDESCRIPTION"Signaling on E1 ISDN Primary Rate interfaces
is always message oriented."OBJECT dsx1TransmitClockSource
SYNTAXINTEGER{
loopTiming(1)}MIN-ACCESSread-onlyDESCRIPTION"The transmit clock is derived from received
clock on ISDN Primary Rate interfaces."OBJECT dsx1Fdl
MIN-ACCESSread-onlyDESCRIPTION"Facilities Data Link usage on E1 ISDN
Primary Rate interfaces.
Note: There is an 'M-Channel' in E1,
using National Bit Sa4 (G.704,
Table 5A). It is used to implement
management features between ET
and NT. This is different from
FDL in T1, which is used to carry
control signals and performance
data. In E1, control and status
signals are carried using National
Bits Sa5, Sa6, and A (RAI Ind.).
This indicates that only the other(1) or
eventually the dsx1Fdl-none(8) bits should
be set in this object for E1 PRI."OBJECT dsx1Channelization
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the channelization is not
required."::={ ds1Compliances 3}ds1Ds2Compliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"Compliance statement for using this MIB for DS2
interfaces."MODULEMANDATORY-GROUPS{ ds1DS2Group }OBJECT dsx1LineType
SYNTAXINTEGER{
dsx1DS2M12(10),
dsx1E2(11)}MIN-ACCESSread-onlyDESCRIPTION"Line type for DS2, E2
interfaces."OBJECT dsx1Channelization
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the channelization is not
required."::={ ds1Compliances 4}ds1NCompliance MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION
"The compliance statement for T1 and E1
interfaces."MODULE-- this moduleMANDATORY-GROUPS{ ds1NearEndConfigurationGroup,
ds1NearEndStatisticsGroup }GROUP ds1FarEndGroup
DESCRIPTION"Implementation of this group is optional for all
systems that attach to a DS1 interface."GROUP ds1NearEndOptionalTrapGroup
DESCRIPTION"Implementation of this group is optional for all
systems that attach to a DS1 interface. If it is
implemented, then ds1NearEndOptionalConfigGroup
should also be implemented."GROUP ds1NearEndOptionalConfigGroup
DESCRIPTION"Implementation of this group is recommended for
all systems that attach to a DS1 interface and
implement ds1NearEndOptionalTrapGroup."GROUP ds1DS2Group
DESCRIPTION"Implementation of this group is mandatory for all
systems that attach to a DS2 interface."GROUP ds1TransStatsGroup
DESCRIPTION"This group is the set of statistics appropriate
for all systems that attach to a DS1 interface
running transparent or unFramed lineType."GROUP ds1ChanMappingGroup
DESCRIPTION"This group is the set of objects for mapping a
DS3 Channel (dsx1Ds1ChannelNumber) to ifIndex.
Implementation of this group is mandatory for
systems that support the channelization of DS3s
into DS1s."
OBJECT dsx1LineType
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line type is not
required."OBJECT dsx1LineCoding
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line coding is not
required."OBJECT dsx1SendCode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the send code is not
required."OBJECT dsx1LoopbackConfig
MIN-ACCESSread-onlyDESCRIPTION"The ability to set loopbacks is not required."OBJECT dsx1SignalMode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the signal mode is not
required."OBJECT dsx1TransmitClockSource
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the transmit clock source is
not required."OBJECT dsx1Fdl
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the FDL is not required."OBJECT dsx1LineLength
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line length is not
required."OBJECT dsx1Channelization
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the channelization is not
required."OBJECT dsx1LineMode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line mode is not
required."OBJECT dsx1LineBuildOut
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line build-out is not
required."::={ ds1Compliances 5}ds1MibT1PriNCompliance MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"Compliance statement for using this MIB for ISDN
Primary Rate interfaces on T1 lines."MODULEMANDATORY-GROUPS{ ds1NearEndConfigurationGroup,
ds1NearEndStatisticsGroup }OBJECT dsx1LineType
SYNTAXINTEGER{
dsx1ESF(2)-- Intl Spec would be G704(2)-- or I.431(4)}MIN-ACCESSread-onlyDESCRIPTION"Line type for T1 ISDN Primary Rate
interfaces."OBJECT dsx1LineCoding
SYNTAXINTEGER{
dsx1B8ZS(2)}MIN-ACCESSread-onlyDESCRIPTION"Type of Zero Code Suppression for
T1 ISDN Primary Rate interfaces."OBJECT dsx1SignalMode
SYNTAXINTEGER{
none(1),-- if there is no signaling channel
messageOriented(4)}MIN-ACCESSread-onlyDESCRIPTION"Possible signaling modes for
T1 ISDN Primary Rate interfaces."OBJECT dsx1TransmitClockSource
SYNTAXINTEGER{
loopTiming(1)}MIN-ACCESSread-onlyDESCRIPTION"The transmit clock is derived from
received clock on ISDN Primary Rate
interfaces."OBJECT dsx1Fdl
MIN-ACCESSread-onlyDESCRIPTION"Facilities Data Link usage on T1 ISDN
Primary Rate interfaces.
Note: Eventually, dsx1Att-54016(4) is to be
used here since the line type is ESF."OBJECT dsx1Channelization
MIN-ACCESSread-onlyDESCRIPTION
"The ability to set the channelization
is not required."OBJECT dsx1LineMode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line mode is not
required."OBJECT dsx1LineBuildOut
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line build-out
is not required."::={ ds1Compliances 6}ds1MibE1PriNCompliance MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"Compliance statement for using this MIB for ISDN
Primary Rate interfaces on E1 lines."MODULEMANDATORY-GROUPS{ ds1NearEndConfigurationGroup,
ds1NearEndStatisticsGroup }OBJECT dsx1LineType
SYNTAXINTEGER{
dsx1E1CRC(5)}MIN-ACCESSread-onlyDESCRIPTION"Line type for E1 ISDN Primary Rate
interfaces."OBJECT dsx1LineCoding
SYNTAXINTEGER{
dsx1HDB3(3)}MIN-ACCESSread-only
DESCRIPTION"Type of Zero Code Suppression for
E1 ISDN Primary Rate interfaces."OBJECT dsx1SignalMode
SYNTAXINTEGER{
messageOriented(4)}MIN-ACCESSread-onlyDESCRIPTION"Signaling on E1 ISDN Primary Rate interfaces
is always message oriented."OBJECT dsx1TransmitClockSource
SYNTAXINTEGER{
loopTiming(1)}MIN-ACCESSread-onlyDESCRIPTION"The transmit clock is derived from received
clock on ISDN Primary Rate interfaces."OBJECT dsx1Fdl
MIN-ACCESSread-onlyDESCRIPTION"Facilities Data Link usage on E1 ISDN
Primary Rate interfaces.
Note: There is an 'M-Channel' in E1,
using National Bit Sa4 (G704,
Table 5A). It is used to implement
management features between ET
and NT. This is different from
FDL in T1, which is used to carry
control signals and performance
data. In E1, control and status
signals are carried using National
Bits Sa5, Sa6, and A (RAI Ind.).
This indicates that only the other(1) or
eventually the dsx1Fdl-none(8) bits should
be set in this object for E1 PRI."OBJECT dsx1Channelization
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the channelization is not
required."OBJECT dsx1LineMode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line mode is not
required."OBJECT dsx1LineBuildOut
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line build-out
is not required."::={ ds1Compliances 7}ds1J1Compliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for T1, J1, and E1
interfaces."MODULE-- this moduleMANDATORY-GROUPS{ ds1NearEndCfgGroup,
ds1NearEndStatGroup }GROUP ds1FarEndNGroup
DESCRIPTION"Implementation of this group is optional for all
systems that attach to a DS1 interface."GROUP ds1NearEndOptionalTrapGroup
DESCRIPTION"Implementation of this group is optional for all
systems that attach to a DS1 interface. If it is
implemented, then ds1NearEndOptionalConfigGroup
should also be implemented."GROUP ds1NearEndOptionalConfigGroup
DESCRIPTION"Implementation of this group is recommended for
all systems that attach to a DS1 interface and
implement ds1NearEndOptionalTrapGroup."GROUP ds1DS2Group
DESCRIPTION"Implementation of this group is mandatory for all
systems that attach to a DS2 interface."GROUP ds1TransStatsGroup
DESCRIPTION"This group is the set of statistics appropriate
for all systems that attach to a DS1 interface
running transparent or unFramed lineType."GROUP ds1ChanMappingGroup
DESCRIPTION"This group is the set of objects for mapping a
DS3 Channel (dsx1Ds1ChannelNumber) to ifIndex.
Implementation of this group is mandatory for
systems that support the channelization of DS3s
into DS1s."OBJECT dsx1LineType
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line type is not
required."OBJECT dsx1LineCoding
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line coding is not
required."OBJECT dsx1SendCode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the send code is not
required."OBJECT dsx1LoopbackConfig
MIN-ACCESSread-only
DESCRIPTION"The ability to set loopbacks is not required."OBJECT dsx1SignalMode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the signal mode is not
required."OBJECT dsx1TransmitClockSource
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the transmit clock source is
not required."OBJECT dsx1Fdl
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the FDL is not required."OBJECT dsx1LineLength
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line length is not
required."OBJECT dsx1Channelization
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the channelization is not
required."OBJECT dsx1LineMode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line mode is not
required."OBJECT dsx1LineBuildOut
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line build-out is not
required."OBJECT dsx1LineImpedance
MIN-ACCESSread-onlyDESCRIPTION
"The ability to set line impedance is not
required."::={ ds1Compliances 8}ds1NMibT1PriNCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"Compliance statement for using this MIB for ISDN
Primary Rate interfaces on T1 lines."MODULEMANDATORY-GROUPS{ ds1NearEndCfgGroup,
ds1NearEndStatGroup }OBJECT dsx1LineType
SYNTAXINTEGER{
dsx1ESF(2)-- Intl Spec would be G704(2)-- or I.431(4)}MIN-ACCESSread-onlyDESCRIPTION"Line type for T1 ISDN Primary Rate
interfaces."OBJECT dsx1LineCoding
SYNTAXINTEGER{
dsx1B8ZS(2)}MIN-ACCESSread-onlyDESCRIPTION"Type of Zero Code Suppression for
T1 ISDN Primary Rate interfaces."OBJECT dsx1SignalMode
SYNTAXINTEGER{
none(1),-- if there is no signaling channel
messageOriented(4)}MIN-ACCESSread-onlyDESCRIPTION"Possible signaling modes for
T1 ISDN Primary Rate interfaces."OBJECT dsx1TransmitClockSource
SYNTAXINTEGER{
loopTiming(1)}MIN-ACCESSread-onlyDESCRIPTION"The transmit clock is derived from
received clock on ISDN Primary Rate
interfaces."OBJECT dsx1Fdl
MIN-ACCESSread-onlyDESCRIPTION"Facilities Data Link usage on T1 ISDN
Primary Rate interfaces.
Note: Eventually, dsx1Att-54016(4) is to be
used here since the line type is ESF."OBJECT dsx1Channelization
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the channelization
is not required."OBJECT dsx1LineMode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line mode is not
required."OBJECT dsx1LineBuildOut
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line build-out
is not required."::={ ds1Compliances 9}ds1NMibE1PriNCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"Compliance statement for using this MIB for ISDN
Primary Rate interfaces on E1 lines."MODULEMANDATORY-GROUPS{ ds1NearEndCfgGroup,
ds1NearEndStatGroup }OBJECT dsx1LineType
SYNTAXINTEGER{
dsx1E1CRC(5)}MIN-ACCESSread-onlyDESCRIPTION"Line type for E1 ISDN Primary Rate
interfaces."OBJECT dsx1LineCoding
SYNTAXINTEGER{
dsx1HDB3(3)}MIN-ACCESSread-onlyDESCRIPTION"Type of Zero Code Suppression for
E1 ISDN Primary Rate interfaces."OBJECT dsx1SignalMode
SYNTAXINTEGER{
messageOriented(4)}MIN-ACCESSread-onlyDESCRIPTION"Signaling on E1 ISDN Primary Rate interfaces
is always message oriented."OBJECT dsx1TransmitClockSource
SYNTAXINTEGER{
loopTiming(1)}MIN-ACCESSread-onlyDESCRIPTION"The transmit clock is derived from received
clock on ISDN Primary Rate interfaces."OBJECT dsx1Fdl
MIN-ACCESSread-onlyDESCRIPTION"Facilities Data Link usage on E1 ISDN
Primary Rate interfaces.
Note: There is an 'M-Channel' in E1,
using National Bit Sa4 (G704,
Table 5A). It is used to implement
management features between ET
and NT. This is different from
FDL in T1, which is used to carry
control signals and performance
data. In E1, control and status
signals are carried using National
Bits Sa5, Sa6, and A (RAI Ind.).
This indicates that only the other(1) or
eventually the dsx1Fdl-none(8) bits should
be set in this object for E1 PRI."OBJECT dsx1Channelization
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the channelization is not
required."OBJECT dsx1LineMode
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line mode is not
required."
OBJECT dsx1LineBuildOut
MIN-ACCESSread-onlyDESCRIPTION"The ability to set the line build-out
is not required."OBJECT dsx1LineImpedance
MIN-ACCESSread-onlyDESCRIPTION"The ability to set line impedance is not
required."::={ ds1Compliances 10}-- units of conformanceds1NearEndConfigGroup OBJECT-GROUPOBJECTS{ dsx1LineIndex,
dsx1TimeElapsed,
dsx1ValidIntervals,
dsx1LineType,
dsx1LineCoding,
dsx1SendCode,
dsx1CircuitIdentifier,
dsx1LoopbackConfig,
dsx1LineStatus,
dsx1SignalMode,
dsx1TransmitClockSource,
dsx1Fdl,
dsx1InvalidIntervals,
dsx1LineLength,
dsx1LoopbackStatus,
dsx1Ds1ChannelNumber,
dsx1Channelization }STATUSdeprecatedDESCRIPTION"A collection of objects providing configuration
information applicable to all DS1 interfaces."::={ ds1Groups 1}
ds1NearEndStatisticsGroup OBJECT-GROUPOBJECTS{ dsx1CurrentIndex,
dsx1CurrentESs,
dsx1CurrentSESs,
dsx1CurrentSEFSs,
dsx1CurrentUASs,
dsx1CurrentCSSs,
dsx1CurrentPCVs,
dsx1CurrentLESs,
dsx1CurrentBESs,
dsx1CurrentDMs,
dsx1CurrentLCVs,
dsx1IntervalIndex,
dsx1IntervalNumber,
dsx1IntervalESs,
dsx1IntervalSESs,
dsx1IntervalSEFSs,
dsx1IntervalUASs,
dsx1IntervalCSSs,
dsx1IntervalPCVs,
dsx1IntervalLESs,
dsx1IntervalBESs,
dsx1IntervalDMs,
dsx1IntervalLCVs,
dsx1IntervalValidData,
dsx1TotalIndex,
dsx1TotalESs,
dsx1TotalSESs,
dsx1TotalSEFSs,
dsx1TotalUASs,
dsx1TotalCSSs,
dsx1TotalPCVs,
dsx1TotalLESs,
dsx1TotalBESs,
dsx1TotalDMs,
dsx1TotalLCVs }STATUSdeprecatedDESCRIPTION"A collection of objects providing statistics
information applicable to all DS1 interfaces."
::={ ds1Groups 2}ds1FarEndGroup OBJECT-GROUPOBJECTS{ dsx1FarEndCurrentIndex,
dsx1FarEndTimeElapsed,
dsx1FarEndValidIntervals,
dsx1FarEndCurrentESs,
dsx1FarEndCurrentSESs,
dsx1FarEndCurrentSEFSs,
dsx1FarEndCurrentUASs,
dsx1FarEndCurrentCSSs,
dsx1FarEndCurrentLESs,
dsx1FarEndCurrentPCVs,
dsx1FarEndCurrentBESs,
dsx1FarEndCurrentDMs,
dsx1FarEndInvalidIntervals,
dsx1FarEndIntervalIndex,
dsx1FarEndIntervalNumber,
dsx1FarEndIntervalESs,
dsx1FarEndIntervalSESs,
dsx1FarEndIntervalSEFSs,
dsx1FarEndIntervalUASs,
dsx1FarEndIntervalCSSs,
dsx1FarEndIntervalLESs,
dsx1FarEndIntervalPCVs,
dsx1FarEndIntervalBESs,
dsx1FarEndIntervalDMs,
dsx1FarEndIntervalValidData,
dsx1FarEndTotalIndex,
dsx1FarEndTotalESs,
dsx1FarEndTotalSESs,
dsx1FarEndTotalSEFSs,
dsx1FarEndTotalUASs,
dsx1FarEndTotalCSSs,
dsx1FarEndTotalLESs,
dsx1FarEndTotalPCVs,
dsx1FarEndTotalBESs,
dsx1FarEndTotalDMs }STATUSdeprecatedDESCRIPTION"A collection of objects providing remote
configuration and statistics information."::={ ds1Groups 3}ds1DeprecatedGroup OBJECT-GROUPOBJECTS{ dsx1IfIndex,
dsx1FracIndex,
dsx1FracNumber,
dsx1FracIfIndex }STATUSdeprecatedDESCRIPTION"A collection of obsolete objects that may be
implemented for backwards compatibility."::={ ds1Groups 4}ds1NearEndOptionalConfigGroup OBJECT-GROUPOBJECTS{ dsx1LineStatusLastChange,
dsx1LineStatusChangeTrapEnable }STATUScurrentDESCRIPTION"A collection of objects that may be implemented
on DS1 and DS2 interfaces."::={ ds1Groups 5}ds1DS2Group OBJECT-GROUPOBJECTS{ dsx1LineIndex,
dsx1LineType,
dsx1LineCoding,
dsx1SendCode,
dsx1LineStatus,
dsx1SignalMode,
dsx1TransmitClockSource,
dsx1Channelization }STATUScurrentDESCRIPTION"A collection of objects providing information
about DS2 (6,312 kbps) and E2 (8,448 kbps)
systems."::={ ds1Groups 6}ds1TransStatsGroup OBJECT-GROUPOBJECTS{ dsx1CurrentESs,
dsx1CurrentSESs,
dsx1CurrentUASs,
dsx1IntervalESs,
dsx1IntervalSESs,
dsx1IntervalUASs,
dsx1TotalESs,
dsx1TotalSESs,
dsx1TotalUASs }STATUScurrentDESCRIPTION"A collection of objects that are the
statistics that can be collected from a DS1
interface that is running transparent or unframed
lineType. Statistics not in this list should
return noSuchInstance."::={ ds1Groups 7}ds1NearEndOptionalTrapGroup NOTIFICATION-GROUPNOTIFICATIONS{ dsx1LineStatusChange }STATUScurrentDESCRIPTION"A collection of notifications that may be
implemented on DS1 and DS2 interfaces."::={ ds1Groups 8}ds1ChanMappingGroup OBJECT-GROUP
OBJECTS{ dsx1ChanMappedIfIndex }STATUScurrentDESCRIPTION"A collection of objects that give a mapping of
DS3 Channel (dsx1Ds1ChannelNumber) to ifIndex."::={ ds1Groups 9}ds1NearEndConfigurationGroup OBJECT-GROUPOBJECTS{ dsx1LineIndex,
dsx1TimeElapsed,
dsx1ValidIntervals,
dsx1LineType,
dsx1LineCoding,
dsx1SendCode,
dsx1CircuitIdentifier,
dsx1LoopbackConfig,
dsx1LineStatus,
dsx1SignalMode,
dsx1TransmitClockSource,
dsx1Fdl,
dsx1InvalidIntervals,
dsx1LineLength,
dsx1LoopbackStatus,
dsx1Ds1ChannelNumber,
dsx1Channelization,
dsx1LineMode,
dsx1LineBuildOut }STATUSdeprecatedDESCRIPTION"A collection of objects providing configuration
information applicable to all DS1 interfaces."::={ ds1Groups 10}ds1NearEndCfgGroup OBJECT-GROUPOBJECTS{ dsx1LineIndex,
dsx1TimeElapsed,
dsx1ValidIntervals,
dsx1LineType,
dsx1LineCoding,
dsx1SendCode,
dsx1CircuitIdentifier,
dsx1LoopbackConfig,
dsx1LineStatus,
dsx1SignalMode,
dsx1TransmitClockSource,
dsx1Fdl,
dsx1InvalidIntervals,
dsx1LineLength,
dsx1LoopbackStatus,
dsx1Ds1ChannelNumber,
dsx1Channelization,
dsx1LineMode,
dsx1LineBuildOut,
dsx1LineImpedance }STATUScurrentDESCRIPTION"A collection of objects providing configuration
information applicable to all DS1 interfaces."::={ ds1Groups 11}ds1NearEndStatGroup OBJECT-GROUPOBJECTS{ dsx1CurrentIndex,
dsx1CurrentESs,
dsx1CurrentSESs,
dsx1CurrentSEFSs,
dsx1CurrentUASs,
dsx1CurrentCSSs,
dsx1CurrentPCVs,
dsx1CurrentLESs,
dsx1CurrentBESs,
dsx1CurrentLCVs,
dsx1IntervalIndex,
dsx1IntervalNumber,
dsx1IntervalESs,
dsx1IntervalSESs,
dsx1IntervalSEFSs,
dsx1IntervalUASs,
dsx1IntervalCSSs,
dsx1IntervalPCVs,
dsx1IntervalLESs,
dsx1IntervalBESs,
dsx1IntervalLCVs,
dsx1IntervalValidData,
dsx1TotalIndex,
dsx1TotalESs,
dsx1TotalSESs,
dsx1TotalSEFSs,
dsx1TotalUASs,
dsx1TotalCSSs,
dsx1TotalPCVs,
dsx1TotalLESs,
dsx1TotalBESs,
dsx1TotalLCVs }STATUScurrentDESCRIPTION"A collection of objects providing statistics
information applicable to all DS1 interfaces."::={ ds1Groups 12}ds1FarEndNGroup OBJECT-GROUPOBJECTS{ dsx1FarEndCurrentIndex,
dsx1FarEndTimeElapsed,
dsx1FarEndValidIntervals,
dsx1FarEndCurrentESs,
dsx1FarEndCurrentSESs,
dsx1FarEndCurrentSEFSs,
dsx1FarEndCurrentUASs,
dsx1FarEndCurrentCSSs,
dsx1FarEndCurrentLESs,
dsx1FarEndCurrentPCVs,
dsx1FarEndCurrentBESs,
dsx1FarEndInvalidIntervals,
dsx1FarEndIntervalIndex,
dsx1FarEndIntervalNumber,
dsx1FarEndIntervalESs,
dsx1FarEndIntervalSESs,
dsx1FarEndIntervalSEFSs,
dsx1FarEndIntervalUASs,
dsx1FarEndIntervalCSSs,
dsx1FarEndIntervalLESs,
dsx1FarEndIntervalPCVs,
dsx1FarEndIntervalBESs,
dsx1FarEndIntervalValidData,
dsx1FarEndTotalIndex,
dsx1FarEndTotalESs,
dsx1FarEndTotalSESs,
dsx1FarEndTotalSEFSs,
dsx1FarEndTotalUASs,
dsx1FarEndTotalCSSs,
dsx1FarEndTotalLESs,
dsx1FarEndTotalPCVs,
dsx1FarEndTotalBESs}STATUScurrentDESCRIPTION"A collection of objects providing remote
configuration and statistics information."::={ ds1Groups 13}END